Mixing and Plugins

How to Master Audio Tracks at Home

Learn how to master audio at home: prepare the mix, use a light chain, hit streaming loudness targets with LUFS and avoid the common mistakes.

On this page
  1. What mastering does
  2. Prepare the mix first
  3. A light home mastering chain
  4. Loudness targets
  5. Check your master
  6. Dither, once and last
  7. AI and automatic mastering
  8. Common mistakes
  9. What does mastering cost?

Mastering is the final polish on a finished mix. At home, the job is to send a well-prepared mix, apply a light chain of processing, check the loudness against streaming targets, and export a clean file. Mastering can’t fix a mix that is unbalanced, so start there.

What mastering does

Mastering makes a finished mix sound consistent across playback systems. It can correct small tonal imbalances, control dynamics a little, and set the final loudness and format. It doesn’t rebuild the mix. If one element is too loud or too quiet, fix that in the mix.

What is a mastering engineer?

A mastering engineer is a specialist who makes the final pass on a mix. They work with a fresh ear, a treated room and specialist tools, and they prepare the file for release. Many home producers master their own tracks, but a professional can help when you need a second opinion or a higher level of polish.

Prepare the mix first

Before you master, make sure the mix is ready:

  • Keep peaks around −6 to −3 dBFS. This leaves headroom for mastering.
  • Remove any limiter from the mix bus. Mastering needs room to work.
  • Balance the mix. Set levels and panning so each element sits in its place.
  • Export a lossless WAV at the mix sample rate, usually 24-bit at 44.1 or 48 kHz.
  • Add short fades to the start and end of clips, and remove pops or clicks at the edit points.

For the mixing side of this, see home mixing basics.

A light home mastering chain

A typical chain has these stages, in this order:

  1. Corrective EQ. Keep moves small, usually ±0.5 to 2 dB with broad Q.
  2. Gentle compression. Aim for a ratio of about 1.5:1 to 2:1 with 1 to 3 dB of gain reduction and a slower attack of 10 to 30 ms. For more on compression, see best free compressor VST plugins for home mixing.
  3. Optional saturation or stereo work. Keep the low end below about 100 to 150 Hz mono, and avoid widening the bass. For more, see stereo width, mono and binaural.
  4. Limiter. Set the ceiling at −1 dBTP for streaming, or −2 dBTP for very loud masters.
  5. Metering and dither. Check the result with metering, then dither once at the end if you’re reducing bit depth.

Keep each stage subtle. If you find yourself making large moves, go back and check the mix. For the same chain with stock plugins, see mixing and mastering in FL Studio.

Loudness targets

Streaming services normalise playback loudness, so the loudness target matters more than the peak level. Measure LUFS (loudness units relative to full scale) over the whole song, not just a short section.

  • Spotify: −14 LUFS integrated, with Loud (−11) and Quiet (−19) settings
  • YouTube and Tidal: about −14 LUFS
  • Apple Music: about −16 LUFS with Sound Check
  • Amazon: about −14 LUFS, though targets vary and change

Many genres are mastered louder than −14 LUFS. Pop and EDM often sit at −9 to −7 LUFS. Normalisation turns these down on playback, so a louder master isn’t automatically better. For a free meter, try the Youlean Loudness Meter. Most DAWs also include one.

Treat −14 LUFS as a playback normalisation level, not a required mastering target. For video uploads, YouTube audio requirements covers the format and loudness in more detail.

Check your master

  • Use true-peak metering. Sample peaks at 0 dBFS can still clip when the audio is converted, so a sample-peak meter can miss problems that a true-peak meter catches.
  • Compare against level-matched references. A/B the master against the mix, and against one or two commercial references, at equal loudness. A louder version almost always sounds better in a quick comparison, which is why matching level matters.
  • Listen on several systems. Check on headphones, car speakers and phone speakers. For a quick listening test, how to turn on mono audio on iPhone explains a mono check you can do on your phone.
  • Take breaks. Ear fatigue is real, so step away every 45 to 60 minutes.

Dither, once and last

Dither only when you reduce bit depth, for example from 24-bit to 16-bit for a CD. Apply it once, as the last process in the chain. Dithering more than once, or on a 24-bit-to-24-bit export, adds nothing useful. For TPDF versus noise-shaped dither, see what dithering is and when to use it.

For the common formats: a CD uses 16-bit at 44.1 kHz, and streaming uploads are usually a 24-bit WAV at the mix sample rate.

AI and automatic mastering

Online and plugin-based services such as LANDR, eMastered and iZotope’s Ozone Master Assistant can produce a quick master. Their features and pricing vary and change over time. Use them as a reference point, and then judge the result by ear against your own reference tracks.

Common mistakes

  • Louder isn’t better on streaming. Over-limited masters are turned down on playback and can sound flatter.
  • Mastering can’t fix a bad mix. Fix balance problems in the mix.
  • Treating −14 LUFS as a rule. It’s a normalisation level, not a target you must hit.
  • Trusting sample peaks. Use true-peak metering instead.
  • Dithering more than once. Dither once, and only when you reduce bit depth.

What does mastering cost?

Prices for professional mastering vary widely by engineer, region and track count. Get quotes from a few engineers, and ask what is included, such as revisions and file formats.

The complete guide to mixing and plugins

Home Mixing Basics and Simple Mixer Software
Read the guide

Keep exploring

Guides from other topics

All topics →