Mixing and Plugins

Home Mixing Basics and Simple Mixer Software

Home mixing basics: free mixer software, recording levels, the mixing order, mix bus headroom and listening levels. Start here before you add plugins.

On this page
  1. Free mixer software
  2. Recording levels and format
  3. The mixing order
  4. Levels and the mix bus
  5. Keep the low end centred
  6. Check the mix
  7. Ear care
  8. Group similar tracks
  9. Common misconceptions
  10. Where to go next

A good home mix starts before any plugin is loaded. It needs a DAW that can route and mix tracks, sensible recording levels, a clear order of work, and a way to check the result on several systems. This guide covers those basics, then points to the detailed articles for each step.

Free mixer software

You don’t need expensive software to start. These free options have full mixers:

  • GarageBand for macOS and iOS
  • Cakewalk by BandLab. Its product line changed in 2024, so check its current status before you rely on it.
  • Tracktion Waveform Free
  • Ardour, which is open source
  • REAPER, with a 60-day full evaluation. A discounted personal licence has been about $60, though the price may change.

Audacity is a free multitrack editor, but it’s not a full mixing console. It has no classic sends or buses, so it’s better for editing than for a complete mix. If you’ve outgrown it, see whether there is a better alternative to Audacity. On Windows, VoiceMeeter (Standard, Banana or Potato) is donationware for routing computer audio between programs.

Recording levels and format

Record at 24-bit, at 44.1 or 48 kHz. That’s the standard home baseline.

Aim for tracking peaks around −12 to −6 dBFS, and an average around −18 dBFS. Mixing at −18 dBFS isn’t too quiet in 24-bit or 32-bit float, and the noise floor isn’t a problem at that level.

Buffer size matters too. Use 64 to 128 samples while recording, for low latency. Switch to 512 to 1024 or more while mixing, for more CPU headroom.

The mixing order

Work in this order:

  1. Gain staging
  2. Static levels
  3. Panning
  4. EQ
  5. Compression
  6. Time effects, such as reverb and delay
  7. Automation

Setting levels and panning before any processing gives you a balance to judge the rest against. For the detail on each stage, see the articles below.

Levels and the mix bus

Leave the mix bus peaks around −6 to −3 dBFS. That gives mastering room to work, so you don’t need a limiter while mixing. Pan law is usually −3 dB by default, though it varies by DAW and is often adjustable.

For what happens at the mastering stage, see how to master audio tracks at home.

Keep the low end centred

Keep the kick, the bass and the lead vocal centred. Below roughly 100 to 150 Hz, keep the mix mono. Widening the low end makes it weaker on phone speakers and club systems. For the wider stereo picture, see stereo width, mono and binaural.

Check the mix

  • Check in mono. Many playback systems are mono or close to it.
  • Check on two or three systems. Use monitors, headphones and a phone or car.
  • Set a sensible monitoring level. Around 75 to 85 dB SPL is typical, and many home mixers prefer about 75 to 79 dB SPL in a small room.
  • Use one to three reference tracks, level-matched to your mix, so you compare like with like.

Ear care

Take a break every 45 to 60 minutes. Ear fatigue sets in quickly, and a fresh ear catches problems you’d otherwise miss.

Protect your hearing as well. The NIOSH limit is 85 dBA for 8 hours, and the allowed time halves for every 3 dB increase.

Group similar tracks

Bus similar tracks together, such as drums or vocals, so you can process and fade them as a group. This saves time and keeps the balance steady.

For how to build parallel buses, see parallel compression explained.

Common misconceptions

  • More plugins don’t make a better mix. Level and balance do most of the work.
  • Free DAWs don’t limit sound quality. Summing is essentially the same across modern DAWs.
  • Soloing a track to EQ it often makes it fit worse. Check each change in the full mix.
  • Headphones alone are workable, but they misrepresent width and low end. Check on speakers too.

Where to go next

Each step in this guide has a fuller article:

Keep exploring

Guides from other topics

All topics →