Mixing and Plugins

What is a high-pass filter in audio?

A high-pass filter passes highs and cuts lows below a cutoff. Learn cutoff and slope, starting frequencies for vocals and bass, and common mistakes.

On this page
  1. How it works
  2. Why use one
  3. Starting points
  4. Mic and preamp switches
  5. Common mistakes

A high-pass filter (HPF) lets frequencies above its cutoff pass through and reduces frequencies below it. It’s also called a low-cut or bass-cut filter. Its cutoff is the −3 dB point, the frequency where the signal is already 3 dB down.

How it works

  • Cutoff: the −3 dB point. Frequencies above it stay mostly intact, and frequencies below it are reduced.
  • Slope: how quickly the lows are reduced, in decibels per octave (dB/oct). Common slopes are 6, 12, 18, 24 and 48 dB/oct. Most people use 12 or 24 dB/oct.
  • Phase: minimum-phase filters shift phase near the cutoff. This is normal and usually harmless.
  • Resonance: a high-Q filter adds a bump just above the cutoff. That’s useful for a special effect, but it’s usually not what you want for cleanup.

What does a low cut mean?

A low cut is another name for a high-pass filter. Some hardware and mixers label it “low cut” instead of “HPF,” so check the label if you’re looking for the same control.

Why use one

  • Rumble and handling noise. A high-pass filter removes air-conditioning hum, traffic rumble, foot taps and wind noise, which sit below the sound you want. For how these differ from hiss and hum, see the different types of noise.
  • Plosives and proximity effect. The “p” and “b” bursts from a vocal, and the bass boost you get when a directional mic is close, are both often tamed with a high-pass filter. For plosives that are already in a recording, see how to remove clicks and pops.
  • Mix muddiness. Many tracks each carry a little low end. Cutting it from the non-bass parts clears space for the kick and bass.

Starting points

These are starting points, not rules:

  • Male vocals: about 80 to 100 Hz
  • Female vocals: about 100 to 150 Hz
  • Acoustic guitar: about 80 to 120 Hz
  • Kick and bass: about 25 to 40 Hz, only to remove subsonic rumble

Set the filter, then sweep the cutoff upward until the source starts to thin. Back off slightly from that point. This keeps the body of the sound.

Use the same ear-first approach for any source. Check the change in the full mix, because a high-pass that sounds fine on solo can make a mix thin.

Mic and preamp switches

Many microphones and preamps have a built-in high-pass switch, usually set at 75, 80 or 100 Hz. Using it while you record can stop rumble from overloading the preamp. The catch is that it’s applied before the signal is saved, so it’s hard or impossible to undo later. If you’re unsure, record flat and filter in the DAW, where you can change it.

For the vocal chain, a high-pass before the compressor stops low rumble from triggering it. For how that fits with compression, see vocal compression for home recording.

Common mistakes

  • High-pass isn’t high-cut. A high-pass removes lows and keeps highs. A high-cut does the opposite. For that filter, see EQ basics: high-cut filters.
  • Filtering everything high. High-passing every track at a steep setting makes the mix thin and lifeless.
  • Expecting it to fix hiss. A high-pass filter won’t reduce hiss or noise in the mid and high range. Use a noise reduction tool for that, and see AI noise removal for audio for options.
  • Forgetting the sound you want. A high-pass can remove too much body from a warm source, so listen in context.

The complete guide to mixing and plugins

Home Mixing Basics and Simple Mixer Software
Read the guide

Keep exploring

Guides from other topics

All topics →