Audio Interfaces

How to Set Up an Audio Interface for Home Recording

Set up an audio interface for home recording: connect it, configure REAPER, set gain and monitoring, and wire an effects loop, step by step.

On this page
  1. What you need before you start
  2. Connect the interface to your computer
  3. Set up REAPER to use the interface
  4. Record your first track
  5. Monitoring: direct or through the DAW
  6. Use an effects loop with your interface
  7. Common setup mistakes
  8. Connect your monitors
  9. When something goes wrong
  10. Other setups in this series
  11. FAQ

What you need before you start

You need an audio interface, a USB cable, a computer, a digital audio workstation (DAW), something to listen through, and a microphone or instrument. The steps below use REAPER as the example DAW. Most DAWs work in a similar way.

Connect the interface to your computer

  • Plug the interface straight into a USB port on the computer. Skip unpowered hubs, which can cause dropouts and detection problems.
  • On Windows, install the maker’s ASIO driver before you connect the interface for the first time, and restart if the installer asks you to.
  • On macOS, most interfaces are class compliant and need no driver. Some still use the maker’s control app for settings.
  • For most home recording, 44.1 kHz or 48 kHz at 24-bit is a sensible choice. 48 kHz is the usual choice for video. Higher rates such as 96 kHz or 192 kHz are not automatically better at home, and they use more CPU and disk space.

Set up REAPER to use the interface

Windows

Open Options > Preferences > Audio > Device. Set Audio system to ASIO, then choose your interface’s driver from the list.

macOS

In the same Audio > Device page, set Audio system to CoreAudio, then select your interface.

Input and output channels

Set the first and last input and output channels so they cover every input and output on the interface. On a 2-in, 2-out interface, for example, the first and last input should cover inputs 1 and 2, and the outputs should cover outputs 1 and 2. If an input you expect isn’t showing up, check these settings first.

Buffer size and latency

Use a buffer of 64 to 128 samples while tracking, to keep latency low. Use 512 to 1024 samples while mixing, which gives the computer more headroom. As a rough guide, 128 samples at 48 kHz is about 2.67 ms one way. Round-trip latency is higher, and the amount depends on the driver and converters in your interface.

Record your first track

  1. Create a track in REAPER.
  2. Set the track’s input to the interface channel your microphone or instrument is plugged into, such as Input 1.
  3. Arm the track for recording.
  4. Set the gain on the interface while you play or speak. Aim for peaks around -12 to -6 dBFS, with average levels near -18 dBFS. You don’t need to record close to 0 dBFS at 24-bit, and doing so risks clipping.

Phantom power

Condenser microphones need 48 V phantom power. Turn it on after the mic is connected, and turn it off before you unplug the mic. Phantom power is generally safe for balanced dynamic mics. Older ribbon mics and damaged cables can be harmed by it, so check the maker’s guidance before you switch it on.

Line or instrument input

Use the Hi-Z or INST input for a guitar or bass played directly. Use line level for keyboards and synths.

Monitoring: direct or through the DAW

Direct monitoring sends the input straight to your headphones with no delay, which is useful while tracking. If you monitor through the DAW instead, turn direct monitoring off. Leaving both on can make the sound doubled or flanged.

Use an effects loop with your interface

An interface effects loop lets you send a signal out of the interface, through a pedal or other outboard gear, and back in. It is not the same as the effects loop on a guitar amp. The basic path is:

Interface line output → pedal or outboard gear → interface input

Keep these points in mind:

  • The loop needs spare outputs beyond the main left and right pair, so an interface with at least four outputs is the usual starting point.
  • Pedals expect an instrument-level signal, and interface outputs are line level. A reamp box, such as the Radial ProRMP, can convert between them.
  • Routing through the loop adds delay. In REAPER, the ReaInsert plugin lets you insert the loop, and its Ping feature measures the delay so the DAW can compensate.

For a closer look at pedals, see can you plug a guitar pedal into an audio interface.

Common setup mistakes

  • Mismatched sample rates. If the operating system, interface and DAW use different sample rates, you can hear clicks or distortion. Match them.
  • Wrong channel range. If inputs don’t show up, check the first and last channel settings.
  • Recording too hot. Peaks near 0 dBFS leave little headroom. Keep the target levels above.

Connect your monitors

Connect the interface’s main left and right outputs to your monitors’ inputs with balanced cables. Turn the computer and the interface on first, and the monitors last. For a full walkthrough, see how to connect studio monitors to an audio interface.

When something goes wrong

If you hear hum, buzz, crackle or hiss, read how to fix static, buzz and digital noise from an audio interface. If the computer doesn’t see the interface at all, read audio interface not detected.

Other setups in this series

FAQ

Is REAPER a good DAW for beginners?

REAPER is a full-featured DAW and has a free evaluation period, so you can try it before deciding. Whether it suits you depends on how you like to work.

How do I set up a MIDI device in REAPER?

Open Options > Preferences > MIDI Devices and enable your controller as an input. Then select it on the track you want to play.

How do I use VST plugins in REAPER?

Once REAPER has scanned your VST plugin folders, you can add plugins from the FX browser on a track.

Do I need a preamp if I have an interface?

Interfaces have built-in mic preamps, so you don’t need an outboard preamp to start. Some people add one for a different sound or for more gain.

Does an audio interface help with latency?

Partly. A good interface and driver let you use a small buffer while tracking, and direct monitoring avoids the computer’s delay in what you hear. Plugins and DAW routing still add delay, which the DAW can compensate for.

What is an effects loop on a guitar amp?

An amp’s effects loop sits between its preamp and power amp, so effects in it act on the amp’s sound. The interface effects loop described above is a separate idea: it sends audio out of the computer’s interface and back in.

Keep exploring

Guides from other topics

All topics →