Audio Editing

How to Fade In and Fade Out Audio in Audacity

Add fade in and fade out effects in Audacity, pick a fade length that suits your audio, use curved fades or the Envelope Tool, and avoid abrupt endings.

On this page
  1. Short answer
  2. Fade in
  3. Fade out
  4. Choosing a fade length
  5. Curved fades
  6. Custom volume curves with the Envelope Tool
  7. Crossfades between clips
  8. Music under narration
  9. Short fades at cut points
  10. Common mistakes

Short answer

Select the part of the track you want to fade, then choose Effect > Fading > Fade In or Fade Out. The fade runs across the whole selection. For a curved fade or a custom shape, use Adjustable Fade, Studio Fade Out, or the Envelope Tool.

Fade in

  1. Select from the start of the track to the point where the sound should reach full level. Click in the track, then press Shift+J to select from the cursor back to the start.
  2. Choose Effect > Fading > Fade In.

The sound rises from silence to full level across the selection. Fade In is linear.

Fade out

  1. Select from the point where the fade should start to the end of the track. Click at the start point, then press Shift+K to select to the end.
  2. Choose Effect > Fading > Fade Out.

Let the fade reach silence before the end of the file, so the file ends cleanly rather than cutting off.

Choosing a fade length

The right length depends on the audio and on taste. Music endings often take several seconds, and podcast intros and outros often use one to three seconds. A fade that’s too long can hide the ending, and one that’s too short sounds abrupt. Listen to the result rather than picking a number from a guide.

Curved fades

A linear fade can sound abrupt near the end. Two tools give smoother curves:

  • Adjustable Fade (Effect > Fading) lets you choose the fade direction, the middle point, and the start and end levels. Presets include S-shaped curves.
  • Studio Fade Out (Effect > Fading) applies a curved fade-out that also reduces high frequencies as the sound fades, which can sound more natural on music.

Custom volume curves with the Envelope Tool

The Envelope Tool (F2) lets you click to add control points and drag them into any volume curve. Envelope points stay editable on the track. Effect fades change the selected audio directly, and you can undo them with Ctrl+Z.

Don’t stack an Envelope change and an Effect fade on the same section. They can add up and make the fade steeper or quieter than you intended.

Crossfades between clips

To blend one sound into another, align the two clips so they overlap, then apply a crossfade. Both options are under Effect > Fading:

  • Crossfade Clips blends two clips on the same track where they meet.
  • Crossfade Tracks blends across two tracks over the section where they overlap.

For stacking layers on separate tracks, see layering and overlapping audio.

Music under narration

A common approach is to keep narration and music on separate tracks, lower the music before the narration starts, and bring it back afterward. The Envelope Tool on the music track is one way to do this. Levels and timing depend on the content, so listen to the mix on speakers and on headphones. The YouTube audio guide gives a rule of thumb for how far below the voice to keep music.

Short fades at cut points

Very short fades, around 5 to 10 ms, at the start and end of a cut can stop a click at the join. This is a different job from a musical fade. For clicks, see removing clicks and pops.

Common mistakes

  • Choosing a fade that’s longer than the part you want to keep.
  • Stacking an Envelope change and an Effect fade on the same section.
  • Using the default linear fade for every ending, when a curve would sound smoother.
  • Expecting a fade to remove silence. Trim the silence separately. See trimming silence.

The complete guide to audio editing

Audio Editing Basics: Splitting and Exporting Tracks in Audacity
Read the guide

Keep exploring

Guides from other topics

All topics →