Audio Editing

How to Remove Clicks and Pops from Audio in Audacity

Remove clicks and pops in Audacity with Click Removal and Repair, fix edit-point clicks with crossfades, and reduce plosive pops with a high-pass filter.

On this page
  1. Short answer
  2. Identify the type of click
  3. Click Removal
  4. Repair a single click
  5. Clicks at edit points
  6. Plosive pops
  7. Dedicated tools
  8. Common mistakes

Short answer

Find the click first, then match the fix to it. For a single click, zoom in and use Repair. For many small clicks, try Click Removal and listen carefully. For clicks at edit points, use short crossfades or fades. For plosive pops, a high-pass filter or a short gain dip can help.

Identify the type of click

  • Edit-point clicks appear after a cut, paste, or delete. The waveform jumps where two pieces don’t line up. On a spectrogram they look like thin vertical lines at the join.
  • Single clicks or spikes come from a mouth noise, a knock, or an electrical glitch.
  • Plosive pops are low-frequency puffs of air on P and B sounds.
  • Dropout clicks come from the recording system, such as buffer underruns. They’re a recording problem, so raise the buffer or latency setting and record again.

To look closely, zoom in with View > Zoom In (Ctrl+1). The spectrogram view, available from the track menu, makes thin spikes easy to see.

Click Removal

Effect > Noise Removal and Repair > Click Removal targets short spikes, like those on vinyl transfers. The defaults are a threshold of 200 and a maximum spike width of 20. A lower threshold and a wider spike width make it more sensitive, so it can also remove sounds you wanted to keep.

Click Removal is a poor fit for mouth clicks. Always preview, and compare before and after.

Repair a single click

  1. Zoom in until you can see individual samples. Press Ctrl+1 repeatedly.
  2. Select only the click. Repair works on very short selections, up to about 128 samples, which is under 3 ms at 44.1 kHz.
  3. Choose Effect > Noise Removal and Repair > Repair. Repair rebuilds the selection from the audio around it, so there must be audio on both sides.

If Repair doesn’t sound right, the Draw tool (F3) can redraw individual samples. It only works at high zoom, when you can see the individual sample dots.

Clicks at edit points

When you paste room tone over noise, or delete a section, the waveform can jump at the join. One Audacity forum user deleted each spike they saw on the spectrogram, and new spikes kept appearing at the same joins. The join itself was the cause.

Try these fixes in order:

  • Cut at zero crossings. Select > At Zero Crossings (Z) moves the selection edges to points where the waveform crosses the centre line.
  • Add short fades. A fade of about 5 to 10 ms at each join often removes the click.
  • Crossfade the join. Effect > Fading > Crossfade Clips blends two clips that meet on the same track. A crossfade is the usual fix when you paste room tone over noisy sections.
  • Remove DC offset. A DC offset can cause a click at each cut. Normalizing with Remove DC offset checked can help (Effect > Volume and Compression > Normalize).

For more on fades, see fading audio in and out.

Plosive pops

P and B sounds can push a burst of low-frequency air into the microphone. The result is a thump rather than a click, so it needs a different fix.

  • A high-pass filter around 80 to 100 Hz often reduces the thump. The right value depends on the voice.
  • A short gain dip over the pop can help. Select only the pop and lower its level.
  • A pop filter and careful microphone placement prevent most of the problem when you record.

Dedicated tools

Dedicated de-clicking tools are built for speech. iZotope RX’s Mouth De-click is one example. They’re worth trying when mouth clicks remain after Audacity’s tools.

Common mistakes

  • Using Noise Reduction for clicks. It targets steady noise, not spikes.
  • Expecting Click Removal to fix every click. It works best on vinyl-style crackle.
  • Repairing long selections. Repair is for a few milliseconds.
  • Treating a plosive as a digital click. The fixes are different.
  • Over-processing. Heavy repair smears transients, so compare each result with the original.

For edits and cut points in a larger project, see audio editing basics.

The complete guide to audio editing

Audio Editing Basics: Splitting and Exporting Tracks in Audacity
Read the guide

Keep exploring

Guides from other topics

All topics →