Short answer
Sample rate is how many times per second a sound is measured. Bitrate is how much data a file uses each second. For uncompressed audio, bitrate follows from sample rate, bit depth and channel count. For lossy files such as MP3 or AAC, you choose the bitrate directly.
For recording, sample rate and bit depth are the settings that matter. When you share a finished file, bitrate is usually the setting you pick.
The three numbers that describe digital audio
- Sample rate is the number of samples taken per second, measured in hertz (Hz). 44.1 kHz means 44,100 samples per second.
- Bit depth is the number of bits used to store each sample. It sets the dynamic range, the gap between the quietest and loudest sounds the file can hold.
- Channels is the number of separate audio streams. Mono is 1 and stereo is 2.
For uncompressed audio:
Bitrate = sample rate × bit depth × channels
Some examples:
| Format | Bitrate | Approximate size per minute |
|---|---|---|
| CD audio: 44.1 kHz, 16-bit, stereo | 1,411.2 kbps | 10.6 MB |
| 48 kHz, 24-bit, stereo | 2,304 kbps | 17.3 MB |
| 96 kHz, 24-bit, stereo | 4,608 kbps | 34.6 MB |
What sample rate controls
Sample rate sets the highest frequency a recording can hold. That ceiling is half the sample rate, known as the Nyquist frequency. At 44.1 kHz it is 22.05 kHz. At 48 kHz it is 24 kHz.
Human hearing reaches about 20 Hz to 20 kHz at best, and the upper limit usually drops with age. Both 44.1 kHz and 48 kHz cover that range. 44.1 kHz is the CD standard for music. 48 kHz is the standard for video, film and broadcast.
Higher rates such as 96 kHz or 192 kHz extend the ceiling beyond what most people can hear. They can still help in specific jobs, such as heavy processing or slowing sounds down. We cover that in is 96kHz recording worth it for a home studio. For the 44.1 vs 48 kHz choice, see is 44.1 kHz or 48kHz better for music.
What bit depth controls
Bit depth sets the noise floor and dynamic range. Each bit adds about 6 dB of dynamic range. 16-bit gives about 96 dB in theory, and 24-bit about 144 dB. Real converters reach roughly 110 to 125 dB, so 24-bit already exceeds what most hardware delivers.
Bit depth does not change the frequency range. Sample rate handles that. For a full comparison of 16-bit, 24-bit and 32-bit float, see bit depth explained.
Bitrate: what the kbps figure means
For lossy formats such as MP3, AAC and Opus, bitrate is the main quality control. The encoder discards information it judges hard to hear, and a higher bitrate keeps more of it. MP3 and AAC files usually use a sample rate of 44.1 or 48 kHz.
MP3 tops out at 320 kbps. Apple Music’s AAC standard is 256 kbps. Lossless formats such as FLAC and ALAC run roughly 700 to 1,100 kbps at CD quality, depending on the music. For specific targets, see what audio bitrate to use.
Which setting to change
For recording, set sample rate and bit depth. A common home-studio choice is 48 kHz / 24-bit WAV. For music-only work, 44.1 kHz / 24-bit is equally valid. Uncompressed files don’t have a bitrate setting to choose.
For sharing, bitrate is the main lever for MP3 and AAC. Pick it for the content: voice, music or video.
Microphone placement, room acoustics, gain staging and the performance usually affect quality far more than sample rate does. Gain staging is covered in what peak level to record at, and mic and room habits in how to record high-quality audio on your computer. Keep your project rate and your interface rate matched to avoid resampling and pitch errors. The audio interface setup guide shows where to set both.
Common misconceptions
- “Higher sample rate means more detail across the board.” It only extends the frequency ceiling above most people’s hearing.
- “Bitrate and bit depth are the same thing.” They aren’t. For uncompressed audio, bitrate is the product of sample rate, bit depth and channels.
- “A high-bitrate file from a low-quality source is better.” Converting an MP3 into a higher-bitrate file does not restore lost detail.
- “A digital signal sounds stepped.” A properly reconstructed digital signal is smooth. The staircase is a way of drawing samples, not the sound itself.
- “All lossless files are the same size.” FLAC and ALAC files vary with the content.