Mixing and Plugins

What Is a Noise Gate and When Should You Use One?

What a noise gate does, its key controls, and when to use one on drums, guitar or podcast voice. Learn the settings, free options and mistakes to avoid.

On this page
  1. The controls
  2. Settings that work
  3. When to use one
  4. Gate or expander
  5. Keep the gate from opening on bleed
  6. Free gates
  7. Set the threshold
  8. Common mistakes

A noise gate mutes or reduces audio when it falls below a set threshold. It only works in the gaps between sounds. It doesn’t remove noise that sits under the signal, so it’s a tool for quiet moments, not a noise cleaner.

The controls

  • Threshold: the level that opens and closes the gate.
  • Attack: how quickly the gate opens.
  • Hold: how long the gate stays open after the signal drops below the threshold.
  • Release: how quickly the gate closes once the hold time has passed.
  • Range: how far the gate reduces the signal when closed.
  • Hysteresis: separate open and close thresholds, which stop the gate from chattering.
  • Key filter (sidechain): filters the trigger signal so bleed from another source doesn’t open the gate.
  • Lookahead: a few milliseconds of delay that lets the gate open before a transient, so the attack isn’t chopped.

Settings that work

These are starting ranges, not fixed rules:

  • Attack: about 0.01 to 1 ms for drums. Slower, 1 to 10 ms, for vocals, to avoid clicks.
  • Hold: about 10 to 100 ms, to keep the gate open through brief dips.
  • Release: about 50 to 300 ms. Match the natural decay of the source.
  • Range: −10 to −20 dB often sounds more natural than a full mute (−∞ dB).

Set the threshold just above the noise floor and below the quietest sound you want to keep.

When to use one

  • Toms and close drum mics. A gate stops spill between hits from making the kit sound washed out.
  • High-gain guitar hiss. A gate can silence the hiss between riffs.
  • Podcast background noise in pauses. A gate can mute the room noise when the speaker isn’t talking.
  • Streaming. Many streamers use the Noise Gate filter in OBS to mute a mic between words.

Gate or expander

An expander is a gentler alternative. Instead of muting quiet signals, it reduces them by a ratio. Use an expander when a gate sounds too abrupt, or when the gap between sounds is small.

Keep the gate from opening on bleed

Bleed can open the gate when you don’t want it to. A common example is a kick drum leaking into a snare mic. Use the key filter to filter the trigger signal, so the gate responds to the sound you care about. Lookahead helps the gate open in time for transients without chopping the attack.

Free gates

  • ReaGate: part of the ReaPlugs package for REAPER. Check the platform before installing.
  • Audacity Noise Gate effect: built into Audacity.
  • Stock DAW gates: most DAWs include one, which is a good starting point.

Set the threshold

Play a passage with the gate active, then move the threshold up until the noise drops out between sounds. Back off until the quiet parts of the sound you want to keep stay open. Listen to the release too, since an abrupt close can sound like an artifact.

Common mistakes

  • Expecting it to clean noise under the signal. A gate only works in the gaps. For noise under speech, see AI noise removal for audio.
  • Setting it too tight. Tight gates chop word endings and reverb tails.
  • Using it instead of a quiet room. A gate is no substitute for a quiet recording space. For a quieter take, see home mixing basics.
  • Gating vocals when editing would do. For vocals, manually trimming silence can sound cleaner than gating.

The complete guide to mixing and plugins

Home Mixing Basics and Simple Mixer Software
Read the guide

Keep exploring

Guides from other topics

All topics →