Quick answer
YouTube accepts many audio formats and re-encodes every upload, so your job is to send a clean, well-levelled file. For most videos, export stereo AAC-LC (or uncompressed PCM in a MOV or MP4) at 48 kHz, with a stereo bitrate of about 384 kbps. Master the mix to around -14 LUFS integrated, with a true peak no higher than -1 dBTP. YouTube doesn’t publish every detail of its processing, so treat these as practical targets.
Recommended upload settings
YouTube’s help documentation lists these recommended settings for uploads:
| Setting | Recommendation |
|---|---|
| Audio codec | AAC-LC (FLAC and linear PCM are also accepted) |
| Sample rate | 48 kHz, the usual video standard |
| Bitrate, mono | 128 kbps |
| Bitrate, stereo | 384 kbps |
| Bitrate, 5.1 surround | 512 kbps |
| Channels | Stereo, or stereo plus 5.1 |
| Container | MP4 with fast start (MOV, MKV and others are accepted) |
What YouTube does after upload
YouTube transcodes your audio after upload. Playback audio is usually Opus or AAC, typically around 128 to 160 kbps for standard streams. For what those numbers mean, see the audio bitrate guide. Some Premium listeners may get higher-bitrate AAC.
The practical result: a 320 kbps MP3 or a lossless file won’t reach viewers unchanged. Upload the best master you can, but don’t expect viewers to hear the difference from a lossless file.
Loudness: what -14 LUFS means
YouTube normalizes playback loudness. Louder videos are turned down toward about -14 LUFS integrated. That target isn’t an official published specification. It’s a figure creators have measured widely. Quieter videos generally aren’t turned up, so a quiet mix will sound quiet on YouTube.
A practical target is about -14 LUFS integrated, with a true peak no higher than -1 dBTP. For spoken-word content, -16 to -14 LUFS sounds consistent with most of YouTube.
Mastering louder than -14 LUFS doesn’t make a video sound louder on YouTube. It just reduces the dynamic range.
Mastering checklist
- Measure the integrated loudness with a LUFS meter. For the full chain, see how to master audio at home. Many editors and DAWs include one, and free meters exist.
- Put a true-peak limiter last in the chain, with its ceiling at -1 dBTP or lower.
- Adjust the level so the integrated loudness sits near -14 LUFS, without peaks passing the ceiling.
- Listen to the final mix for clicks or distortion from the limiter.
- Export AAC at 48 kHz, with a stereo bitrate of about 384 kbps to match YouTube’s recommendation.
Music under voice
Dialogue should lead the mix. A common rule of thumb is to keep music 15 to 20 dB below the voice. Trim some midrange from the music bed, around 1 to 4 kHz, so the voice sits clearly on top. Keep the main dialogue centered.
Check how YouTube played your video
Right-click the video while it plays and open Stats for nerds. Look for a volume or content loudness value, such as “Volume / Normalized.” Labels vary by player and over time. This shows how much YouTube adjusted the playback volume.
Common mistakes
- Assuming 44.1 kHz is required. It isn’t. 48 kHz is the video standard. See 44.1 kHz vs 48 kHz.
- Expecting viewers to hear a lossless file. YouTube re-encodes every upload.
- Mastering very loud to beat other videos. The level gets turned down anyway.
- Letting music sit too close to the voice. Dialogue should stay clear.
FAQ
Does YouTube support high-res audio?
You can upload higher-resolution audio, such as 24-bit PCM. YouTube re-encodes it for playback, so most viewers hear a lossy version.
What are the standard video dimensions for YouTube?
Most YouTube videos use a 16:9 frame. The common sizes are 1920 by 1080 (HD) and 3840 by 2160 (4K). YouTube accepts other sizes too.
Related guides
For recording levels and capture settings before you export, see the computer audio recording guide. If you’re narrating your video, see how to record a voiceover at home on a budget.