Short answer
When recording at 24-bit, aim for peaks around -12 to -6 dBFS, with average levels near -18 dBFS. Sources disagree on this. Some guides aim lower, with peaks around -18 dBFS, which is a conservative choice that leaves more room for surprises. Either way, keep peaks well below 0 dBFS, the digital maximum.
What dBFS means
dBFS measures level relative to digital full scale. 0 dBFS is the highest level a digital system can represent, and anything above it clips. Negative values sit below full scale. -6 dBFS is about half the amplitude of 0 dBFS, and -12 dBFS is about a quarter.
Analog meters work differently. On many analog setups, 0 VU was calibrated to around -18 dBFS, though the exact value varied by gear.
Why 0 dBFS is a hard ceiling
A digital signal can’t go above 0 dBFS. When a signal exceeds that line, it is clipped. The result is harsh, unmusical distortion, and it can’t be fully repaired after recording.
Peaks are often unexpected. A singer’s sudden shout or a drum hit can exceed a level that looked safe during a quiet take. Headroom gives you room for those moments.
Why recording hot doesn’t help in 24-bit
The habit of recording as loud as possible comes from tape. Tape added noise, so engineers pushed levels higher to keep the signal-to-noise ratio up, and hot tape saturated in a way many people liked.
Digital works differently. At 16-bit, the dynamic range is limited, so the advice to record hot lingered. At 24-bit, the noise floor sits far below normal recording levels, so you don’t need to get close to 0 dBFS to get a clean signal. Digital recording doesn’t add the saturation that made hot tape sound good, so recording hot mostly adds clipping risk. Pushing entry-level or mid-range preamps hard can also harm the sound.
Peaks vs average
- Peak is the highest instantaneous level. Clipping depends on peaks, and digital meters show them.
- Average (often shown as RMS) is a rough measure of perceived level across a passage. It helps you judge a take’s overall level.
Sources with a big gap between peaks and average need more headroom. Drums, percussive guitar and loud vocals with sudden shouts are examples. For very dynamic sources, aim for peaks near -10 dBFS or lower.
Many analog-modeling plugins expect input around -18 dBFS. Running them hot can add distortion of their own.
How to set the level
- Lower your monitor or headphone level first. A sudden loud burst can hurt your ears.
- Ask the performer for the loudest passage. That’s the chorus, the hardest strum or the biggest shout.
- Set the preamp or interface gain so the meter peaks in your target range during that passage. On a Scarlett 2i2, the setup guide covers the gain controls, including Auto Gain on the 4th Gen.
- Record a test take and check the file, not just the meter in the moment. A brief red light isn’t always audible clipping, but check.
- Re-record if a peak reaches 0 dBFS. Lowering the DAW fader afterwards can’t remove clipping that happened at the interface. Why audio clips in FL Studio explains which kinds of clipping can be recovered.
For how 32-bit float fits in, see bit depth explained.
Levels beyond tracking
Targets change as the project moves forward.
- Mix bus: many engineers leave roughly -6 to -3 dBFS of peak headroom before mastering. This is a convention, and engineers vary.
- Masters: a -1 dBTP true-peak ceiling is common for streaming. Some very loud masters use -2 dBTP.
- Loudness: streaming services normalize playback. Spotify and YouTube target about -14 LUFS, and Apple Music about -16 LUFS. These targets change, so check current guidance. For a chain that works to them, see how to master audio tracks at home.
Peak level and loudness (LUFS) are different measurements. Peak tells you where the highest point is. LUFS tells you how loud the piece feels over time.
For the next step down to 16-bit, see what is dithering and when should you use it.
Common misconceptions
- “Record as hot as possible.” That’s a tape-era habit. At 24-bit it adds clipping risk without improving the sound.
- “The meter colors tell you when you’re clipping.” Interface meter colors aren’t standardized. Check the actual dBFS values.
- “A red light means the take is ruined.” Not always, but check the file and re-record if the peak reached 0 dBFS.