Audio Interfaces

How to Fix Static, Buzz and Digital Noise from an Audio Interface

Find out what kind of noise your audio interface makes, then fix hum, buzz, crackle and hiss with grounding, cabling, buffer and gain settings.

On this page
  1. Find the type of noise first
  2. Fix hum and buzz from a ground loop
  3. Fix crackles, clicks and pops
  4. Fix hiss and a noisy signal
  5. What won’t fix it
  6. When to suspect the interface
  7. FAQ

Find the type of noise first

The sound usually tells you the cause. Match what you hear to the table below, then change one thing at a time so you can see what helped.

What you hear Likely cause Try this first
Steady hum at 60 Hz (US) or 50 Hz (UK and EU) Ground loop, or unbalanced cables Put everything on one power strip, and check the cables
Buzz with a harsh, rich tone Hum with harmonics, often from dimmers, LED drivers, fluorescent lights or power bricks Move audio cables away from power and lighting
Crackle, clicks or pops Buffer underruns, or driver and sample rate settings Raise the buffer to 256–512 samples; match sample rates
Hiss Low gain that was boosted later, or self-noise from the mic or preamp Raise gain at the source; check the mic and cable
A rhythmic “dit-dit” buzz Phone radio-frequency (RF) interference Move phones away from the setup
Noise that changes with mouse movement or CPU load Digital noise coming through USB or the power supply Try a different USB port, and avoid unpowered hubs

A quick test: unplug the microphone or instrument. If the noise stops, it’s coming from the input chain. If it continues, the problem is further along the chain, in the computer, the interface or the power. Then run the laptop on battery. If the hum stops, a ground loop through the charger is a likely cause.

Fix hum and buzz from a ground loop

Hum and buzz often come from a ground loop, which happens when two or more devices are connected to ground at different points.

  • Plug the computer, the interface and the monitors into the same power strip or outlet.
  • Use balanced TRS or XLR cables from the interface to your monitors. Unbalanced RCA or TS cables invite hum.
  • Keep audio cables away from power cords, dimmers, LED drivers, fluorescent lights and power bricks.
  • Try a different USB port, and avoid unpowered hubs. If the hum stays, a USB isolator, such as those from Intona or iFi, can help.
  • For line-level hum, a DI box or an isolation transformer with a ground lift can break the loop.

Safety: never remove the mains earth pin, and never use a cheater plug to cure hum. The earth pin is a safety connection. If the hum persists, ask a qualified electrician or the device’s maker to check the wiring.

Not all hum is a ground loop. Unbalanced cable runs and nearby transformers can also cause it.

Fix crackles, clicks and pops

Crackles, clicks and pops are often digital problems, such as buffer underruns or driver settings. They are less often a sign of a faulty interface.

  • Raise the buffer to 256–512 samples while you record. Lower it only when you need low latency.
  • Make sure the sample rate matches across the operating system, the interface and the DAW. A mismatch can cause clicks or distortion.
  • On Windows, use the High performance power plan, turn off USB selective suspend, and check DPC latency with a tool such as LatencyMon.
  • Close Wi-Fi, Bluetooth and background apps while you test for dropouts.
  • On Windows, use the manufacturer’s ASIO driver rather than a generic Windows audio driver.

Fix hiss and a noisy signal

  • Get enough gain at the source. Set the gain on the interface so your peaks sit around -12 to -6 dBFS. Boosting a weak signal later also boosts its noise.
  • Low-output microphones may need extra gain. Some low-output dynamic mics, such as the Shure SM7B, can need about 60 dB of gain. An inline booster such as the Cloudlifter adds about 25 dB, and it needs 48 V phantom power.
  • Keep guitar pickups away from electronics. Single-coil pickups hum near monitors, screens and fluorescent lights. Turn or move away from them.
  • Swap cables one at a time. A broken shield can cause intermittent crackle.

What won’t fix it

  • Expensive “audiophile” cables don’t cure ground loops. Balanced wiring does.
  • A noise gate or denoiser can hide noise, but it won’t fix the cause. Use one for cleanup after you have fixed the source.
  • Digital crackle is rarely a faulty interface. Check the buffer, driver and power settings first.
  • Hum isn’t always a ground loop. Unbalanced runs and nearby transformers can cause it too.

For a glossary of the different noise types, see what are the different types of noise.

When to suspect the interface

If the noise continues after these steps, try the interface on a different computer, with a different cable and a different power outlet. If it still crackles or hums, contact the maker.

FAQ

Why is my mic making a buzzing noise?

A buzz from a microphone is often hum from a ground loop, a noisy cable, or nearby power lines and lighting. Check the cable first, then move the setup away from power and try the single-power-strip fix.

Why is my USB port making noise?

Computer USB ports can carry digital noise from the computer itself, and front-panel ports and hubs are more prone to it. Connect the interface directly to a rear port, and avoid unpowered hubs.

My audio interface is making a crackling noise. How can I fix it?

Start with the buffer size, the sample rate and the driver, as described above. If the crackle continues, check the cables and power.

Why does my audio sound staticky?

Static is usually hiss from low gain or a noisy cable, or a digital problem such as the buffer or driver. Unplug the input, as described in the quick test above, to tell which.

What does noise suppression mean?

Noise suppression reduces background noise by processing the signal. It can change the sound of the recording, so use it as cleanup, and fix the source where you can.

What is digital noise?

In audio work, “digital noise” usually means clicks, crackle and dropouts that come from the computer, the USB connection or the driver. Quantization noise, a much quieter effect of bit depth, is a separate idea.

The complete guide to audio interfaces

How to Set Up an Audio Interface for Home Recording
Read the guide

Keep exploring

Guides from other topics

All topics →