Audio Interfaces

How to Connect Studio Monitors to an Audio Interface

Connect studio monitors to an audio interface with balanced cables, a safe power-on order and matched levels, then place them for an accurate mix.

On this page
  1. Connect the line outputs to the monitor inputs
  2. Turn everything down and off first
  3. Choose the right cables
  4. Connect left to left and right to right
  5. Power on in the right order
  6. Set the levels
  7. Place the monitors
  8. Add a subwoofer
  9. Avoid the headphone output for monitors
  10. Protect your hearing
  11. Common mistakes

Connect the line outputs to the monitor inputs

Connect the interface’s main left and right line outputs to the monitors’ inputs. Use balanced cables where you can. Turn the volume down before you connect anything, and turn the monitors on last.

Turn everything down and off first

Before you connect, turn the volume on the interface and on each monitor all the way down, and switch the monitors off. Loud pops can damage tweeters and your hearing.

Choose the right cables

  • Balanced cables are the usual choice: TRS-to-TRS (1/4-inch) or TRS-to-XLR. A TRS-to-XLR cable has a male XLR end for a monitor with an XLR input. Balanced cables resist hum better.
  • Unbalanced RCA or TS cables work, but they’re more prone to hum, especially over long runs.
  • XLR outputs: some interfaces have XLR outputs. Match them to the monitor inputs.

Connect left to left and right to right

Look for outputs labelled Main L and Main R, or Outputs 1 and 2. Connect the left output to the left monitor, and the right output to the right monitor.

To check the connections, play a track panned hard left, then hard right. Each sound should come from the correct speaker.

Power on in the right order

Turn on the computer and the interface first, and the monitors last. When you finish, power off in reverse: monitors first, then the interface.

Set the levels

  • Monitor input sensitivity: if your monitor has an input sensitivity switch and your interface is a pro-audio model, +4 dBu is usually the setting to use. Check both manuals.
  • Rear volume: set each monitor’s rear volume to the same fixed point, often the centre position. Then control the listening level with the interface’s monitor knob.
  • Balance the two controls: maxing the monitors’ rear knobs while keeping the interface low can add noise. Set both so neither is working at its limit.
  • Mixing level: many engineers mix at around 79 to 85 dB SPL. Smaller rooms often work at 73 to 79 dB SPL. These are rules of thumb, not targets.

Place the monitors

  • Form a triangle. Position the monitors and your listening position as the three points of an equilateral triangle.
  • Set the tweeters at ear height. Angle them toward your ears.
  • Keep the monitors away from walls. Pushing them against a wall boosts the bass and can make the low end misleading. If space is tight, use the monitor’s boundary or port EQ switches.
  • Centre yourself between the side walls. The “38% rule” suggests placing your listening position about 38% of the room’s length from the front wall. It’s a rule of thumb.

Add a subwoofer

A subwoofer usually sits between the interface and the monitors. Crossover settings vary by model. A crossover around 80 Hz is a common starting point.

Avoid the headphone output for monitors

Connect the monitors to the line outputs, not the headphone output. Use the headphone output only as a last resort, because it’s designed for headphones.

Protect your hearing

Keep long sessions below about 85 dB SPL to limit the risk of hearing damage. Turn levels down before you connect anything.

Common mistakes

  • Expecting speaker wire or an amplifier. Powered monitors need neither.
  • Thinking XLR means microphone only. XLR is also the standard balanced line connector.
  • Pushing monitors against the wall. See the placement section above.

For the full setup path, including buffer size and effects loops, see how to set up an audio interface for home recording. If you hear hum from your monitors, see how to fix static, buzz and digital noise from an audio interface.

The complete guide to audio interfaces

How to Set Up an Audio Interface for Home Recording
Read the guide

Keep exploring

Guides from other topics

All topics →