Recording in FL Studio follows a few steps: set up the audio device, choose an input on a mixer track, arm the track, set your levels, then record. Audio recording needs Producer Edition or higher. The Fruity Edition does not record audio into the Playlist.
What you need
- An audio interface, or another audio input, with a driver for your computer. See how to set up an audio interface if it’s new.
- A microphone or instrument. A condenser microphone needs +48 V phantom power, which most audio interfaces can supply.
- Headphones for monitoring, so the sound from speakers does not bleed back into the microphone.
- FL Studio Producer Edition or higher.
Step 1: Set up the audio device
Open Options > Audio Settings (F10). On Windows, choose your interface’s ASIO driver. On macOS, choose the interface’s Core Audio device. While you track, set the buffer to 128 to 256 samples. Make sure the sample rate matches your interface, usually 44.1 kHz or 48 kHz. The audio settings guide explains each option.
Step 2: Choose an input on a mixer track
- Open the Mixer with F9.
- Select an empty insert track.
- Open the input menu at the top of the track’s FX slot panel, and choose your input.
For a single microphone or guitar, pick a mono input, such as In 1. For a stereo source, pick a stereo pair, such as In 1–2. A stereo input for a mono microphone puts the sound on one side only.
Step 3: Arm the track and choose the record mode
- Click the track’s record button (the disk icon) below the fader to arm it.
- Press the main Record button (R), and choose Audio, so the take goes into the Playlist as an audio clip. You can also choose Edison.
Press Ctrl+M to turn on the metronome. The countdown setting is in the recording options.
Step 4: Set your levels
Sing or play at the loudest level you expect, and watch the meter on the mixer track and on your interface. Aim for peaks of about -12 to -6 dBFS, with averages lower. If the meter reaches 0 dBFS, lower the interface’s gain. Clipped input cannot be repaired later, so it is worth taking a little time here. Record at 24-bit for more headroom.
Turn on phantom power only after the microphone is connected, and with your monitors turned down. Many guides suggest turning phantom power on last.
For more on why clipping cannot be repaired, see why audio clips in FL Studio.
Step 5: Record and stop
Press Space to start playback and recording. Press Space again to stop. The take appears in the Playlist as a waveform. If it does not, check that FL Studio is in Song mode, and that the record mode is set to audio.
Record several takes
Loop recording creates several takes, so you can choose the best one. The take-handling options are in the recording settings. Layering a few takes can add depth. When you do this, pan the layers slightly left and right so they do not stack in the centre.
Monitor without delay
Monitoring through FL Studio adds the buffer’s delay, which can make you sound late in your headphones. If that happens, turn on direct monitoring on your interface, and check that the armed track is not sending the input back through FL Studio. The latency guide explains this in more detail.
Microphone placement
Mic placement affects the sound as much as any setting. As a starting point for vocals, try a distance of about 6 to 12 inches from the mouth, with a pop filter to reduce plosives. Angling the microphone slightly off-axis can reduce harsh sibilance. Whatever gets through can be tamed later with a de-esser. Test a few positions and listen to each one.
Common mistakes
- Arming a track without choosing its input. The track needs an input before it records anything.
- Choosing a stereo input for a mono microphone. The sound ends up on one side.
- Recording too hot. Peaks at 0 dBFS cannot be fixed later.
- Monitoring through speakers with the microphone open. Use headphones to avoid feedback.
Next steps
To tidy up a take, see cutting, merging and reversing audio clips in FL Studio. If your take comes out silent, check why an FL Studio recording is silent.